Cool Running (Water Pump)

Your vehicle is like you in a way. When it gets hot, it needs to be cooled down. And one of the key parts to keeping it cool is the water pump.

Now, that’s a bit of a misnomer. It IS a pump, but it’s pumping coolant, not pure water. Cooling off your engine is vital since it builds up heat when it creates power by burning fuel. Your water pump acts as a way to recirculate that coolant. It goes through a series of tubes and hoses through the engine where it picks up heat, then is sent off to the radiator to get rid of that heat. Cooled off, the coolant is recycled through the water pump to start the journey again.

The water pump works by taking mechanical power from the engine, usually from a belt. Obviously, that belt has to be in good condition and adjusted properly or else the water pump won’t be able to do its job.

Here are some things to look for that will signal problems with your water pump. If your heat gauge is erratic or showing a much higher than normal temperature, that could be a sign of trouble. Another is if you hear a whine under the hood. And if that gets louder when you go faster, get it checked right away. You may see steam coming out from under the hood or coolant may be leaking.

These signs signal that it’s time for you to have a technician check to see where the problem is. Some water pumps are powered by a timing belt. If your vehicle has that design and your timing belt is due for replacement, sometimes it’s a good idea to replace the water pump too, even if it’s working properly. That’s because the labor to replace the timing belt can be expensive and it may be wise to proactively take care of the water pump while it’s disassembled.

Your service advisor will explain the options available and offer the best path to keeping your water pump doing its job. Your engine’s life depends on it.

Autotronics of St. Peter
111 Jefferson Avenue
St. Peter, MN 56082
507.934.9290
http://autotronicsstpeter.com

How Cool is That! (Coolant level sensor replacement)

Your vehicle’s engine runs hot. It should, since it’s a series of little explosions that create the power that gets you going where you want to go. To keep the engine cool, engineers have designed wonderful cooling systems that use liquid coolant, hoses, and a radiator to transfer the heat from the engine to the outside air.

In order for the system to work right, it has to have the right amount of that liquid coolant in it. So that you know when the coolant has dipped below the correct amount, there is a sensor that keeps an eye on it. When the coolant gets low, that sensor lights up a signal on the dash to alert you. It may literally say “Check Coolant” or it may have a picture that looks like an old-style bulb thermometer sitting in liquid. Your owner’s manual will usually tell you exactly what the one in your vehicle looks like.

If that sensor system isn’t working right, you could wind up driving for a long time with not enough coolant in the engine, and the excess heat can cause some extensive—and expensive—damage.

There are a couple of ways you will know if something’s wrong with your coolant level sensor. One is when you top off the coolant tank, and the low coolant light stays on. If you suspect yours might be having a problem, bring it in so we can thoroughly check your coolant system.

If it is a sensor, we can run a test to see where the problem is in your cooling system. It could be a bad sensor, but it also could be that there is something causing your coolant level to be low. If the sensor needs replacing, the technician will replace it, fill your coolant level to the manufacturer’s recommended level, and test for any leaks in the system. Really, how cool is that?

Autotronics of St. Peter
111 Jefferson Avenue
St. Peter, MN 56082
507.934.9290
http://autotronicsstpeter.com

test

Full Stop (Brake Master Cylinder Replacement)

When you step on your brake pedal, you want to feel confident that your vehicle’s going to stop. If your brakes aren’t working right, it’s a risk to your safety and the safety of others on the road. After all, you’re driving a machine that weighs thousands of pounds, and you have to be able to stop that big machine quickly and with control, especially with some of the speeds you travel on the highways.

The heart of your vehicle’s brake system is the master cylinder. When you apply the brakes, the master cylinder has pistons, springs, and brake fluid. That fluid amplifies and distributes the force of your foot through brake lines to calipers at all your wheels. Those calipers squeeze down on rotors or discs, which is what slows down and stops your vehicle.

For safety, a master cylinder has two cylinders, one for two wheels, and the other for the remaining two wheels. That way, if there is a failure in one, you’ll still have braking power at half your wheels.

The master cylinder doesn’t last forever, of course, and here are some signs it may have problems. When you press on the brake pedal, it feels soft and spongy. You may see the brake light on your instrument panel go on. You may notice brake fluid leaking, or it may be discolored.

All of those are signs of brakes that need attention, and among the possible culprits is a master cylinder that has failed. When you bring it in for a technician to look at, they’ll check not only the master cylinder but also the rest of the components, such as pads, discs, shoes, brake lines, and hoses. If your master cylinder needs replacing, we’ll make sure all the other parts meet the manufacturer’s specs as well.

Brakes are important. Really important. Full stop.

Autotronics of St. Peter
111 Jefferson Avenue
St. Peter, MN 56082
507.934.9290
http://autotronicsstpeter.com