Monthly Archives: June 2014

Autotronics of St. Peter: Why Replace Your Engine Air Filter?

Just as our bodies need clean air to function properly, your vehicle engine needs clean air to operate efficiently. Let’s go egghead for a minute. For every gallon of gas we burn driving on St. Peter streets, 20 pounds of carbon dioxide comes out the tailpipe. Question: how can a gallon of gas that weighs a little over six pounds produce 20 pounds of carbon dioxide?

The answer is that the carbon comes from the gasoline, but the oxygen comes from the air. You see, it takes about 12,000 gallons of air to burn a gallon of gas in your engine. Clearly, your vehicle needs a lot of air to keep going in St. Peter. A lot of clean air is best.

drive

You’ve seen the pictures of people in Japan wearing face masks. They want some kind of filter to keep unwanted pollution and germs out of their lungs. Well, your vehicle also works better when its internals are clean. When your vehicle air filter is dirty, it simply can’t trap any more dirt, so the pollutants just pass through into your air intake system. From there it can clog your fuel injectors and even get into the motor itself. Not surprisingly, burning dust and pollen in your vehicle engine does you no good.

Replacing a dirty air filter at Autotronics of St. Peter in St. Peter can improve your fuel economy by up to 10 percent. At today’s St. Peter fuel prices, you should be able to pay for a new air filter before your next oil change.

The verdict: When your vehicle engine air filter needs to be replaced; it needs to be replaced. How often depends entirely on the level of air pollution where you drive in MN. A simple visual inspection at Autotronics of St. Peter in St. Peter will tell you when you need a new engine air filter.

Autotronics of St. Peter
111 Jefferson Avenue
St. Peter, MN 56082
507.934.9290
http://autotronicsstpeter.com


Stop It! You Need Good Brakes

Good brakes are obviously very important. If you’ve ever had your brakes go out while you’re driving around the Cleveland area, you’ll know how terrifying it can be. Today we’ll focus on how to tell when you have a brake problem, and how to make good repair choices.

Often, the first indication that something’s wrong with the brakes is an unusual sound. It could be a squeal, chatter or grinding sound.

Some brake pads have a little piece of metal embedded in them that will make a squeal or chirping sound when the brake pads have been worn down to the point that they need to be replaced. It’s an early warning indicator.

When you hear that sound, schedule an appointment at Autotronics of ST Peter soon.

Now a chattering sound is more urgent. That usually indicates that something is loose. It could be a brake pad or even the brake calipers. If one of those parts falls off, you could have some serious trouble stopping the vehicle. It would be a good idea to park it until you can get into the shop.

A grinding noise usually means that the brake pad is completely worn away and the metal parts of the brake are rubbing directly on the metal brake rotor. That means the rotor is being damaged and will need some work. More on that later.

Another warning sign is that your brake pedal may feel soft and spongy – or it may even feel very hard to push in. Both could mean trouble. And of course, you may get a dashboard brake warning light.

Now when it comes time to replace your brake pads, you have a choice to make. You can get the same pads that came standard on your vehicle. You can expect the same performance and durability as with the pads that came on the car from the factory.

Now you can also get a budget brake pad. Sometimes drivers insist on lower cost pads. That’s OK if the budget demands it, but you need to be aware of the trade offs. Lower grade pads are usually noisier, so you’ll have to live with more noise when you apply the brakes. They also tend to generate a lot more brake dust, you know, that black dust that accumulates on your wheels. And they probably won’t last as long either. In our opinion, that’s a lot of compromise for just a few dollars in savings.

You can also choose to buy premium brakes pads. These perform at higher specifications than the factory pads. You can expect quieter operation, less brake dust and better stopping power.

Now, getting back to the rotors. The rotors are the discs that the brake pads clamp down on to stop the vehicle. If you’ve been driving with completely worn brake pads, you’ve scratched grooves into the rotors. If the grooves aren’t too deep, the rotor can be resurfaced. A thin layer of metal is cut off the surface of the rotor to make it smooth again.

Now, if the grooves are too deep or if the rotor has already be resurfaced before, there may not be enough material to resurface and still have a rotor that’s thick enough to safely stop the vehicle. In that case, the rotor will have to be replaced.

Something that’s often overlooked is the brake fluid. Your manufacturer has a recommended schedule for evacuating the old brake fluid, cleaning the system and refilling it with fresh brake fluid. This is really important to brake performance.

So here’s the bottom line: if you suspect, inspect. If you notice any of these warning signs, have your brakes inspected. Your advisor can help you make the repair decision that’s right for you.

Stop It! You Need Good Brakes

Good brakes are obviously very important. If you’ve ever had your brakes go out while you’re driving around the St. Peter area, you’ll know how terrifying it can be. Today we’ll focus on how to tell when you have a brake problem and how to make good repair choices.

Often, the first indication that something’s wrong with the brakes is an unusual sound. It could be a squeal, chatter or grinding sound.

Some brake pads have a little piece of metal embedded in them that will make a squeal or chirping sound when the brake pads have been worn down to the point that they need to be replaced. It’s an early warning indicator.

When you hear that sound, schedule an appointment at Autotronics of St. Peter soon.

Now a chattering sound is more urgent. That usually indicates that something is loose. It could be a brake pad or even the brake calipers. If one of those parts falls off, you could have some serious trouble stopping the vehicle. It would be a good idea to park it until you can get into the shop.

A grinding noise usually means that the brake pad is completely worn away and the metal parts of the brake are rubbing directly on the metal brake rotor. That means the rotor is being damaged and will need some work. More on that later.

Another warning sign is that your brake pedal may feel soft and spongy – or it may even feel very hard to push in. Both could mean trouble. And of course, you may get a dashboard brake warning light.

Now when it comes time to replace your brake pads, you have a choice to make. You can get the same pads that came standard on your vehicle. You can expect the same performance and durability as with the pads that came on the car from the factory.

Now you can also get a budget brake pad. Sometimes St. Peter drivers insist on lower cost pads. That’s OK if the budget demands it, but you need to be aware of the tradeoffs. Lower grade pads are usually noisier, so you’ll have to live with more noise when you apply the brakes. They also tend to generate a lot more brake dust, you know, that black dust that accumulates on your wheels. And they probably won’t last as long either. In our opinion, that’s a lot of compromise for just a few dollars in savings.

You can also choose to buy premium brakes pads at Autotronics of St. Peter. These perform at higher specifications than the factory pads. You can expect quieter operation, less brake dust and better stopping power.

Now, getting back to the rotors. The rotors are the discs that the brake pads clamp down on to stop the vehicle. If you’ve been driving with completely worn brake pads, you’ve scratched grooves into the rotors. If the grooves aren’t too deep, the rotor can be resurfaced. A thin layer of metal is cut off the surface of the rotor to make it smooth again.

Now, if the grooves are too deep or if the rotor has already be resurfaced before, there may not be enough material to resurface and still have a rotor that’s thick enough to safely stop the vehicle. In that case, the rotor will have to be replaced.

Something that’s often overlooked is the brake fluid. Your manufacturer has a recommended schedule for evacuating the old brake fluid, cleaning the system and refilling it with fresh brake fluid. This is really important to brake performance.

So here’s the bottom line: if you suspect, inspect. If you notice any of these warning signs, have your brakes inspected at Autotronics of St. Peter in St. Peter. Your service advisor can help you make the repair decision that’s right for you.

Autotronics of St. Peter
111 Jefferson Avenue
St. Peter, MN 56082
507.934.9290
http://autotronicsstpeter.com