Tag Archives: Brakes

It’s Brake Time (Brake Calipers)

Race car drivers have demonstrated the advantages of disc brakes, so most modern vehicles use them.  Sometimes just the front wheels have disc brakes, but many vehicles now have them all the way around. 

A major component of the disc brake is called a caliper.  It works by squeezing brake pads against the disc or rotor, kind of like a bicycle hand brake.  The brake pads themselves are what contact the rotor, causing friction to build and the wheel to slow down, but it’s the calipers that apply the pressure to the pads.

Caliper design has evolved over the years, and there are two common types.  One is called a floating caliper.  It has one or two pistons on one side of the disc. When you push down the brake pedal, the piston or pistons in your caliper put pressure on that one side.  A mechanism connected on the other side of the disc applies pressure as well, squeezing your disc so the vehicle stops.  Floating calipers are less expensive since they have fewer parts.

The other type is called a fixed caliper.  They use pistons on both sides of the disc, sometimes several.  They are often used in more high-performance or heavy-duty vehicles.

Calipers can have rubber seals to keep out dirt, debris and moisture, but when that rubber wears out, sometimes the calipers can get contaminated.  They can stick or start leaking; they can even rust.  Then your caliper can get stuck applying that “squeeze” when you are not pressing on the brake pedal.  Or they can get stuck in the other position, not applying stopping power when you press the pedal.

When this happens, it’s not unusual to feel your vehicle pull to one side when you brake.  You might notice a burning smell from the constant friction if the caliper is stuck on, plus you may feel the heat from the wheel after you park and get out of your vehicle.  Sometimes you’ll hear a high-pitched sound or clunk if your calipers are binding up. 

That’s your cue to have them checked out at your vehicle service center.  If your calipers aren’t working correctly, it can be a safety hazard.  Sticking calipers can affect your ability to steer and stop; this is the kind of “brake time” you need so you can get them back on track and working properly.

Autotronics of St. Peter
111 Jefferson Avenue
St. Peter, MN 56082
507.934.9290
http://autotronicsstpeter.com

Full Stop (Brake Master Cylinder Replacement)

When you step on your brake pedal, you want to feel confident that your vehicle’s going to stop.  If your brakes aren’t working right, it’s a risk to your safety and the safety of others on the road.  After all, you’re driving a machine that weighs thousands of pounds, and you have to be able to stop that big machine quickly and with control, especially with some of the speeds you travel on the highways. 

The heart of your vehicle’s brake system is the master cylinder.  When you apply the brakes, the master cylinder has pistons, springs, and brake fluid.  That fluid amplifies and distributes the force of your foot through brake lines to calipers at all your wheels.  Those calipers squeeze down on rotors or discs, which is what slows down and stops your vehicle.

For safety, a master cylinder has two cylinders, one for two wheels, and the other for the remaining two wheels.  That way, if there is a failure in one, you’ll still have braking power at half your wheels.

The master cylinder doesn’t last forever, of course, and here are some signs it may have problems.  When you press on the brake pedal, it feels soft and spongy.  You may see the brake light on your instrument panel go on.  You may notice brake fluid leaking, or it may be discolored. 

All of those are signs of brakes that need attention, and among the possible culprits is a master cylinder that has failed.  When you bring it in for a technician to look at, they’ll check not only the master cylinder but also the rest of the components, such as pads, discs, shoes, brake lines, and hoses.  If your master cylinder needs replacing, we’ll make sure all the other parts meet the manufacturer’s specs as well. 

Brakes are important.  Really important. Full stop.

Autotronics of St. Peter
111 Jefferson Avenue
St. Peter, MN 56082
507.934.9290
http://autotronicsstpeter.com

Them’s the Brakes (Brake Rotor Resurfacing)

Your vehicle’s brakes wear out.  It’s inevitable. You’ll notice it when you step on the brake pedal and feel it harder to stop, or there’s vibration when you are braking. 

Most modern vehicles have disc brakes that each use a brake pad that press on a disc (disc brakes!) called a rotor.  The friction between them enables you to stop, and each time you do a little bit of the pad and the rotor wears down.

The original brakes on vehicles used a rotor that was thick enough to last through at least two replacements of the pads.  But vehicle manufacturers who want to save costs and weight now make them thinner, and sometimes the rotors have to be replaced after the first pad replacement.  But not always.

Vehicle manufacturers specify a minimum thickness to provide safe braking.  Sometimes rather than having to have your rotors replaced, they can be put on a lathe and resurfaced.  In other words, the surfaces of the disc can be slightly shaved off so the surface is flat and doesn’t wobble. 

Whenever you bring your vehicle in to have the brakes checked, the technician will measure the thickness of the rotors to see if they can be resurfaced without leaving them too thin for safe braking. If they can, with the right tools and skill, the rotors can be resurfaced.  If not, the rotors should be replaced. 

Discuss the options with your service advisor.  Our service center can recommend replacements that are designed to help stop your vehicle as well as or better than the vehicle’s original rotors.

Either way, keep in mind that keeping your brakes in top condition can supply the margin of safety that may one day save your life or the lives of those around you.

Autotronics of St. Peter
111 Jefferson Avenue
St. Peter, MN 56082
507.934.9290
http://autotronicsstpeter.com